Padrões físico-químicos

Reagecon's Yttrium Standard for ICP; ICP-MS 1000 µg/mL (1000 ppm) in 2-5% Nitric Acid (HNO₃) for ICP or ICP-MS is manufactured from ultra-pure metal (99.999%). This product is manufactured gravimetrically using the mass balance approach: 100% less the sum of all impurities (w/w). Prior to bottling; the final product is tested and verified using ICP-MS and is reported using the gravimetric result; corrected for density. To a specification of ± 0.2%. The results are reported in mg/kg and mg/L on the basis of weight and density. Reagecon hold ISO 17025 accreditation (A2LA Ref: 6739.02) for calibration of laboratory balances. - GHS/OSHA compliant, REACH - This product is produced in a highly controlled cleanroom (ISO 7) environment, using ultra-pure water (specially treated for the production of mass spectroscopy standards), triple distilled acids and triple leached pre-cleaned bottles. The titrimetry and spectroscopy are controlled and calibrated using separate standards, so the product comes with two layers of traceability including NIST Standards, where available. All of the uncertainties of measurement for this product are calculated according to Eurachem/CITAC guidelines and reported as expanded uncertainties at the 95% confidence level.

Reagecon's Conductivity Standard at 25°C Certified Reference Material is produced under our ISO 17034 (A2LA Ref: 6739.01) Accreditation and is NIST traceable. The product is aqueous based; non-hazardous and accurate to a specification of ± 1%. - To enable analysts to achieve the correct result when measuring conductivity and to prove the correctness of that result; Reagecon has developed a high quality range of Conductivity Standards; which can be used for calibration of conductivity sensors; quality control; method validation and instrument qualification. - ISO 17034 accreditation requirements include raw material characterisation; homogeneity and stability studies; assignment of certified values as well as packaging and documentation control. - Reagecon Conductivity Standards are aqueous based; thereby eliminating any errors attributable to matrix mismatch. - Directly traceable to NIST Standard Reference Materials; meets the specification requirements of all the major Pharmacopoeias. - The low temperature coefficient of variation; reduces measurement errors and enables non-temperature controlled use and is suitable for field work. - High accuracy ± 1% at 25°C; enables the Standards to be used as calibrators and/or controls; in accordance with the most exacting industrial requirements. - Manufactured to exacting specifications with an extended shelf life and stability; even after opening the bottle thereby eliminating the requirement to open a fresh bottle of Standard every time it is used.

Reagecon's Multi Element Standard for ICP; ICP-MS in 5-10% Nitric Acid (HNO₃); ICH Q3D is manufactured from ultra-pure metals or salts. This product is manufactured gravimetrically using the mass balance approach: 100% less the sum of all impurities (w/w). Prior to bottling; the final product is tested and verified using ICP-MS and is reported using the gravimetric result; corrected for density. The results are reported in mg/kg and mg/L on the basis of weight and density. Reagecon hold ISO 17025 (A2LA Ref: 6739.02) accreditation for calibration of laboratory balances. - GHS/OSHA compliant, REACH - This product is produced in a highly controlled cleanroom (ISO 7) environment, using ultra-pure water (specially treated for the production of mass spectroscopy standards), triple distilled acids and triple leached pre-cleaned bottles. The titrimetry and spectroscopy are controlled and calibrated using separate standards, so the product comes with two layers of traceability including NIST Standards, where available. All of the uncertainties of measurement for this product are calculated according to Eurachem/CITAC guidelines and reported as expanded uncertainties at the 95% confidence level. Description | Concentration: - Silver (Ag): 150 µg/mL (ppm). - Arsenic (As): 15 µg/mL (ppm). - Cadmium (Cd): 5 µg/mL (ppm). - Cobalt (Co): 50 µg/mL (ppm). - Mercury (Hg): 30 µg/mL (ppm). - Nickel (Ni): 200 µg/mL (ppm). - Lead (Pb): 5 µg/mL (ppm). - Selenium (Se): 150 µg/mL (ppm). - Thallium (Tl ): 8 µg/mL (ppm). - Vanadium (V): 100 µg/mL (ppm).

Reagecon's Conductivity Standard at 25°C Certified Reference Material is produced under our ISO 17034 (A2LA Ref: 6739.01) Accreditation and is NIST traceable. The product is aqueous based; non-hazardous and accurate to a specification of ± 1%. - To enable analysts to achieve the correct result when measuring conductivity and to prove the correctness of that result; Reagecon has developed a high quality range of Conductivity Standards; which can be used for calibration of conductivity sensors; quality control; method validation and instrument qualification. - ISO 17034 accreditation requirements include raw material characterisation; homogeneity and stability studies; assignment of certified values as well as packaging and documentation control. - Reagecon Conductivity Standards are aqueous based; thereby eliminating any errors attributable to matrix mismatch. - Directly traceable to NIST Standard Reference Materials; meets the specification requirements of all the major Pharmacopoeias. - The low temperature coefficient of variation; reduces measurement errors and enables non-temperature controlled use and is suitable for field work. - High accuracy ± 1% at 25°C; enables the Standards to be used as calibrators and/or controls; in accordance with the most exacting industrial requirements. - Manufactured to exacting specifications with an extended shelf life and stability; even after opening the bottle thereby eliminating the requirement to open a fresh bottle of Standard every time it is used.

Reagecon's Conductivity Standard at 25°C Certified Reference Material is produced under our ISO 17034 (A2LA Ref: 6739.01) Accreditation and is NIST traceable. The product is aqueous based; non-hazardous and accurate to a specification of ± 1%. - To enable analysts to achieve the correct result when measuring conductivity and to prove the correctness of that result; Reagecon has developed a high quality range of Conductivity Standards; which can be used for calibration of conductivity sensors; quality control; method validation and instrument qualification. - ISO 17034 accreditation requirements include raw material characterisation; homogeneity and stability studies; assignment of certified values as well as packaging and documentation control. - Reagecon Conductivity Standards are aqueous based; thereby eliminating any errors attributable to matrix mismatch. - Directly traceable to NIST Standard Reference Materials; meets the specification requirements of all the major Pharmacopoeias. - The low temperature coefficient of variation; reduces measurement errors and enables non-temperature controlled use and is suitable for field work. - High accuracy ± 1% at 25°C; enables the Standards to be used as calibrators and/or controls; in accordance with the most exacting industrial requirements. - Manufactured to exacting specifications with an extended shelf life and stability; even after opening the bottle thereby eliminating the requirement to open a fresh bottle of Standard every time it is used.

Reagecon's Conductivity Standard at 25°C Certified Reference Material is produced under our ISO 17034 (A2LA Ref: 6739.01) Accreditation and is NIST traceable. The product is aqueous based; non-hazardous and accurate to a specification of ± 1%. - To enable analysts to achieve the correct result when measuring conductivity and to prove the correctness of that result; Reagecon has developed a high quality range of Conductivity Standards; which can be used for calibration of conductivity sensors; quality control; method validation and instrument qualification. - ISO 17034 accreditation requirements include raw material characterisation; homogeneity and stability studies; assignment of certified values as well as packaging and documentation control. - Reagecon Conductivity Standards are aqueous based; thereby eliminating any errors attributable to matrix mismatch. - Directly traceable to NIST Standard Reference Materials; meets the specification requirements of all the major Pharmacopoeias. - The low temperature coefficient of variation; reduces measurement errors and enables non-temperature controlled use and is suitable for field work. - High accuracy ± 1% at 25°C; enables the Standards to be used as calibrators and/or controls; in accordance with the most exacting industrial requirements. - Manufactured to exacting specifications with an extended shelf life and stability; even after opening the bottle thereby eliminating the requirement to open a fresh bottle of Standard every time it is used.

Pricing displayed is Nett. For order quantities above 4 units, ask your sales contact for a quotation. Reagecon’s Multi Element Anion Standard for Ion Chromatography (IC) in H₂O is manufactured from ultra-pure salts. This product is manufactured gravimetrically. Prior to bottling; the final product is tested and verified using a state of the art ion chromatograph and is reported using the gravimetric result; corrected for density. The results are reported in mg/kg and mg/L on the basis of weight and density. Reagecon hold ISO 17025 accreditation (A2LA Ref: 6739.02) for calibration of laboratory balances. - GHS/OSHA compliant, REACH - This product is produced in a highly controlled cleanroom (ISO 7) environment; using ultra-pure water (specially treated for the production of ion chromatography standards) and triple leached pre-cleaned bottles. All of the uncertainties of measurement for the product are calculated according to Eurachem/CITAC guidelines and reported as expanded uncertainties at the 95% confidence level. Description | Concentration: - Flerovium (Fl): 50 µg/mL (ppm). - Chloride (Cl⁻): 50 µg/mL (ppm). - Bromide (Br⁻): 50 µg/mL (ppm). - Nitrite (NO₂): 50 µg/mL (ppm). - Nitrate (NO₃): 50 µg/mL (ppm). - Phosphate (PO₄³): 50 µg/mL (ppm). - Sulphate (SO₄²): 50 µg/mL (ppm).

Reagecon Total Acid Number (TAN) Standard 4.5 mg/g Potassium Hydroxide (KOH) in Synthetic Base Oil Matrix is tested by our ISO 17025 Accredited Test Method (A2LA Ref: 6739.03). This high quality standard can be used to calibrate; control or validate the methodology or equipment used to perform TAN testing according to ASTM Method D664. - Produced in accordance with ASTM D664. - The TAN test method D664 is used to indicate relative changes that occur in oil during use under oxidising conditions regardless of the colour or other properties of the oil. - The test method D664 is also used as a guide in quality control of lubricating oil formulations or as a measure of lubricant degradation. - Standards are traceable to NIST. - The method has a very low uncertainty of measurement which is linked to the TAN value and is expressed as a percentage of that value. - Stability is proven (either opened or unopened) for the shelf life of this product. - This Standard forms part of the linearity set of TAN Standards that range in value from 0.5 mg/g KOH in a synthetic base oil up to 4.5 mg/g KOH. - Consistency of product - Independent; Traceable; Certified.

Reagecon's Starch Indicator 0.5% (w/v) Solution is a high quality Indicator Solution produced from the highest quality raw materials and manufactured and tested under rigorous conditions. For manual titrations; indicator titrant or analyte change colour and this colour change is by far the most important method of end point detection, in such titrations. A high quality indicator solution such as Reagecon's Starch Indicator 0.5% (w/v) Solution facilitates end point detection, in a clear and unambiguous manner and is an imperative for accurate manual titrimetry.

Reagecon's Lanthanum Standard for Atomic Absorption (AAS) 1000 µg/mL in 1M Nitric Acid (HNO₃) is manufactured from very pure metal or salt (at least 99.9%). This product is manufactured gravimetrically. Prior to bottling; the final product is tested and verified using ICP-MS and is reported using the gravimetric result; to a specification of ± 0.2%. The results are reported in mg/L on the basis of weight). Reagecon hold ISO 17025 accreditation (A2LA Ref: 6739.02) for calibration of laboratory balances. - GHS/OSHA compliant, REACH - This product is produced in a highly controlled cleanroom (ISO 7) environment, using ultra-pure water (specially treated for the production of mass spectroscopy standards). The titrimetry and spectroscopy are controlled and calibrated using separate standards, so the product comes with two layers of traceability including NIST Standards where available. All of the uncertainties of measurement for this product are calculated according to Eurachem/CITAC guidelines and reported as expanded uncertainties at the 95% confidence level.

Reagecon's Potassium Phosphate pH 6.8 and 0.5% Sodium Dodecyl Sulphate Dissolution Media Concentrate is presented in concentrate form. This concentrate measures 961.5ml in volume in each bottle and the contents of each bottle can be diluted to produce 25L of working solution in water. This diluted volume is the working Dissolution Medium. The product is prepared and when diluted can be used in accordance with relevant pharmacopoeia requirements. - This product is presented as a concentrate in order to facilitate easy shipping, storage and handling. - The pack contains 6 bottles, each of which has a volume of 961.5ml of solution, each 961.5ml bottle is diluted to give 25L of ready to use Dissolution Medium.

This Reagecon's 400 mV (± 5mV) Standard acts as a Control or Reference Material. This is because Redox Oxidation/Reduction (ORP) is an absolute measurement and the sensing electrode does not require calibration. This Standard verifies the functionality of the sensing and reference electrode; the analysts technique; environmental conditions and the operation of the measuring meter. The value of 400 mV quoted refers to the potentials of the platinum electrode v Ag/AgCl reference electrode. - Reagecon produces a complete range of high-quality Redox Standards for the control; validation or qualification of Redox measurement. - Very high specification (± 5mV). - Manufactured to exacting specifications with an extended shelf life and stability; even after opening the bottle. - All products are tested with proven verifiable accuracy and fully budgeted uncertainty of measurement.

This standard is an aqueous suspension of a formazin type product that carries all of the advantages of formazin but eliminates its shortcomings. It is stable; safe; EPA approved and accurate. - Reagecon have developed a proprietary synthetic process that produces a family of products called Turbiform™. These products combine most of the positive attributes of the formazin and AMCO APEA-1 range of standards already available from Reagecon; whilst eliminating most of the shortcomings. Most importantly; this process does not interfere adversely with the status of formazin as the recognised primary standard. - Product exhibits a wide range of particle sizes; shapes and slopes (similar to formazin) mean diameter 3 µm with distribution of between 1 and 20 microns; which are similar to the particle size and distribution found in most sample types. - This product can be used to calibrate; control; validate or qualify; almost any make or model of Turbidity measuring instrument. - Traceable to NIST reference material 1690 and 1691 - Can be used to calibrate; control; validate or qualify almost any make or model of instrument

Reagecon's Platinum-Cobalt (Hazen) 1000 Colour Standard can be used to calibrate, control, qualify or validate colour measurement instruments. This standard can be described as Platinum-Cobalt, Pt-Co, Hazen or APHA colour. All descriptions are interchangeable. This product is used extensively in the water industry and several other industries. The standard covers the requirements of ASTM Method D 1209.

Pricing displayed is Nett. For order quantities above 4 units, ask your sales contact for a quotation. Reagecon’s Atomic Absorption Multi Element Standard is manufactured from very pure metal or salt (at least 99.9%). This product is manufactured gravimetrically. Prior to bottling; the final product is tested and verified using ICP-MS and is reported using the gravimetric result; to a specification of ± 0.2%. The results are reported in mg/L on the basis of weight). Reagecon hold ISO 17025 (A2LA Ref: 6739.02) accreditation for calibration of laboratory balances. - GHS/OSHA compliant, REACH - This product is produced in a highly controlled cleanroom (ISO 7) environment, using ultra-pure water (specially treated for the production of mass spectroscopy standards). The titrimetry and spectroscopy are controlled and calibrated using separate standards, so the product comes with two layers of traceability including NIST Standards where available. All of the uncertainties of measurement for this product are calculated according to Eurachem/CITAC guidelines and reported as expanded uncertainties at the 95% confidence level. Description | Concentration: - Silver (Ag): 0.75 µg/mL (ppm). - Zinc (Zn): 0.75 µg/mL (ppm).

Reagecon Total Base Number (TBN) Standard 3.0 mg/g Potassium Hydroxide (KOH) in Synthetic Base Oil Matrix is tested by our ISO 17025 Accredited Test Method (A2LA Ref: 6739.03). This high quality standard can be used to calibrate; control or validate the methodology or equipment used to perform TBN testing according to ASTM Method D2896. - Produced in accordance with ASTM D2896. - Test method D2896 is used for both new and used petroleum products that may contain basic constituents that may be present as additives. - The test method D2896 may also be used as a measure of lubricant degradation; but any condemning limits based on the test must be established on an individual basis. - Standards are traceable to NIST. - The method has a very low uncertainty of measurement. - Stability is proven (either opened or unopened) for the shelf life of this product. - This Standard forms part of the linearity set of TBN Standards that range in value from 1.0 mg/g KOH in a synthetic base oil up to 70 mg/g KOH. - Consistency of product - Independent; Traceable; Certified.

Reagecon’s N44 Kinematic Viscosity, Dynamic Viscosity and Density Standard can be used to calibrate, control or validate all types of viscometers including capillary, flow cup, rotational, falling ball, falling/rising object, stabinger and vibrational viscometers.This Viscosity Standard and all Reagecon Viscosity Standards are reported to 4 significant figures on their Certificate of Analysis.Only 2 significant figures are shown here for expediency of layout.   - This product has been tested according to ASTM method D 2162 for Kinematic Viscosity using Ubbelohde Master Viscometers. - The Density has been tested in accordance with ASTM method D4052 (Kinematic Viscosity x Density = Dynamic Viscosity). - Kinematic Viscosity values and Density values are traceable to the Primary Standard of pure water at 20°C as adopted by NIST. Temperature values are traceable via National Standards to the ITS-90 temperature scale.

Reagecon's Refractive Index Standards (Stabilised Sucrose) 1.33299 nD at 20°C is a high quality product; with an extended shelf life to be used either as a calibrant or analytical control material for use in Refractive Index based methods for Refractive Index determination. This product can be used on any make or model of refractometer. The product is tested using a state of the art refractometer; manufactured gravimetrically and is traceable. - High accuracy (± 0.00014 nD units) - Tested using a state of the art Refractometer

Pricing displayed is Nett. For order quantities above 4 units, ask your sales contact for a quotation. Reagecon’s Multi Element Anion Standard for Ion Chromatography (IC) in H₂O is manufactured from ultra-pure salts. This product is manufactured gravimetrically. Prior to bottling; the final product is tested and verified using a state of the art ion chromatograph and is reported using the gravimetric result; corrected for density. The results are reported in mg/kg and mg/L on the basis of weight and density. Reagecon hold ISO 17025 accreditation (A2LA Ref: 6739.02) for calibration of laboratory balances. - GHS/OSHA compliant, REACH - This product is produced in a highly controlled cleanroom (ISO 7) environment; using ultra-pure water (specially treated for the production of ion chromatography standards) and triple leached pre-cleaned bottles. All of the uncertainties of measurement for the product are calculated according to Eurachem/CITAC guidelines and reported as expanded uncertainties at the 95% confidence level. Description | Concentration: - Fluoride (F⁻): 1000 µg/mL (ppm). - Chloride (Cl⁻): 1000 µg/mL (ppm). - Sulphate (SO₄²): 1000 µg/mL (ppm). - Nitrite (NO₂): 1000 µg/mL (ppm). - Nitrate (NO₃): 1000 µg/mL (ppm). - Phosphate (PO₄³): 1000 µg/mL (ppm).

Pricing displayed is Nett. For order quantities above 4 units, ask your sales contact for a quotation. Reagecon’s Multi Element Anion Standard for Ion Chromatography (IC) in H₂O is manufactured from ultra-pure salts. This product is manufactured gravimetrically. Prior to bottling; the final product is tested and verified using a state of the art ion chromatograph and is reported using the gravimetric result; corrected for density. The results are reported in mg/kg and mg/L on the basis of weight and density. Reagecon hold ISO 17025 accreditation (A2LA Ref: 6739.02) for calibration of laboratory balances. - GHS/OSHA compliant, REACH - This product is produced in a highly controlled cleanroom (ISO 7) environment; using ultra-pure water (specially treated for the production of ion chromatography standards) and triple leached pre-cleaned bottles. All of the uncertainties of measurement for the product are calculated according to Eurachem/CITAC guidelines and reported as expanded uncertainties at the 95% confidence level. Description | Concentration: - Chloride (Cl⁻): 100 µg/mL (ppm). - Nitrate (NO₃): 100 µg/mL (ppm). - Sulphate (SO₄²): 100 µg/mL (ppm). - Nitrite (NO₂): 100 µg/mL (ppm).